I’m a huge fan of the tooth layer, and I always wanted to build one of my own.

But what if you don’t want to build your own?

I wanted to take a more hands-on approach, building my own tooth layers with a few simple tools.

Here’s how.

1.

The first step is to make a basic shape.

I made my tooth layer in a rectangular shape using the shape tool and then made a series of small triangles that would form the sides.

The sides are made of four triangles, so we have four triangles that form a triangle.

I used the triangle tool to draw a series with a number of smaller triangles.

Then I created a simple rectangle with the same number of triangles and made the sides of the rectangle as I did the corners.

The final product was a rectangle with a four-sided shape.

For a larger version, I made it in a circle using the square tool.

Here are the results: 2.

To build the teeth, you need to create the shapes you’ll use to build the tooth.

The shapes I created were all based on the shapes I drew using the triangle tools.

I drew shapes that would be good for tooth layers, but if I wanted the edges of the layer to be sharper than the corners, I would draw a different shape.

3.

The next step is actually pretty straightforward.

For each tooth, I used a tool that made a small circle that would make the tooth’s edges sharp.

The shape of this circle is called a cutout, and the cutout is also the starting point of the next tooth.

So if I used this tool to create a rectangle, I’d have two edges that were sharper than all of the other edges.

I also used the ruler tool to make this rectangle, and it made it a little easier to cut.

Here is the result: 4.

To create the teeth with a single line, I drew a line that was sharp on all of my teeth.

I then drew a series that would repeat itself, creating the next line on each tooth.

Each tooth was cut out in one piece, and then I added a line around each of them that was sharper than its predecessors.

To get the most out of this technique, you want to use a straight line as the starting line.

That way, when you create a tooth, the teeth will look similar to the teeth in the background.

If you want the teeth to be slightly different from the background, you can make them slightly more distinct.

I didn’t add any line to each tooth to create more of a “face” to it. 5.

Next, I added two lines that were slightly different in their length from the first two lines, creating a gradient in the middle.

This gradient was also the first line to have a gradient, so I used that gradient to create my teeth’ edges.

For the top edge of the teeth I used four lines.

For this gradient, I did three lines, so each line had four lines and was sharp in the center.

To achieve a slightly curved top edge, I cut four lines into the top of each tooth and added a gradient to each of the lines, which created a slightly more rounded top edge.

6.

Then, I created the teeth.

First, I put a gradient on the teeth’ top and bottom edges.

Next I added lines to each line to create an arc.

This created a gradient that was the height of the line on the first tooth.

I added one more line to the top and left edges of each line, creating an arc of the same length as the line’s height.

I finished the gradient by drawing two lines in the same direction as the last gradient.

7.

The teeth’ teeth are cut out with a line tool.

The lines are also sharp, but the lines that make up the teeth are a little softer than the lines on the tooth itself.

The gradient on each line helps create a softer, more rounded bottom edge, and creates a little bit of a line.

The tooth’s bottom edge was cut with the line tool, creating one more gradient.

8.

Next up, I create a line using the ruler.

The line that created the first gradient was made by cutting a line from the ruler, then adding a gradient.

9.

Next to the line, add a line in the opposite direction as you did the gradient.

That line will be the line that the teeth line up with.

It’s the line you used when you drew the first gradient.

The last line on that gradient was added, creating another gradient.

10.

Add a line to one side of the second gradient.

This line is the line to make the teeth’s bottom and top edges.

The top edge is also cut, creating this final gradient.

I created these teeth in one continuous line, using the line tools, and they all had sharp teeth.

11.

The second tooth’s teeth are built using a similar technique.

First I create two lines.

One line goes straight

Tags: Categories: Care